Assembler Installer Doors B
Posted on: September 22, 2022
Job ID 00000330414 Date posted 07/12/2022 Location Renton,
Washington; Everett, Washington Company
At Boeing, we innovate and collaborate to make the world a better
place. From the seabed to outer space, you can contribute to work
that matters with a company where diversity, equity and inclusion
are shared values. We're committed to fostering an environment for
every teammate that's welcoming, respectful and inclusive, with
great opportunity for professional growth. Find your future with
The Boeing Company is seeking Assembler Installer Doors to join our
teams supporting Boeing Commercial Airplanes in either our Renton
or Everett locations in Washington State! This is an exciting
opportunity to install, rig and adjust door parts and assemblies
into aircraft body structures .
Mechanics in this position install, rig and adjust door parts and
assemblies into aircraft body structures. They may set up and
perform some functional and operational tests of all door
* Locate work area using drawings which specifies airplane number,
section number, and three-point location.
* Obtain and verify kitted (pre-picked) detail parts, standards,
and assemblies were issued correctly.
* Ensure that parts issued are effective for the airplane and are
free of visible defects.
* If parts are not pre-picked, get parts and ensure that parts
selected are effective for the airplane and are free of visible
* Set up assembly tools per tooling instructions or drawing.
* Review bar chart or automated time line to determine which job to
work on and obtain appropriate drawings for job.
* Drill, ream, countersink close tolerance holes and install
fasteners in parts/assemblies per drawing using correct tools
(e.g., drill motor, rivet gun, torque wrench).
* Locate door assembly to airplane structure, install close
tolerance bolt(s) and bushings/spacers for initial door
* Align door assembly to roller fittings, guides and latch tracks.
Check door swing into fuselage. Adjust fit using door rigging
tools. Ensure door has correct fit and fair with fuselage when
closed. Align scuff plate. Shim and trim door for fit using
planers, rotary sanders and hand files.
* Install door hardware including warning sensor, pressure/bulb
seal, liner brackets, bustle hardware and other attachments. Check
seals for gaps and light leaks. Check door handle and hinges for
proper angle using a protractor and/or inclinometer and adjust.
Perform seal check on door installation, as required. Utilize
vacuum pressurization equipment on exterior of door and check for
leaks using an ultrasonic leak detector on interior surfaces.
* Install personnel evacuation slides, life rafts, and components
(e.g., high pressure and explosive bottles, thrusters, battery), as
required. Assist in slide deployment checks to ensure proper
* Coordinate with other ongoing tests on the aircraft. Lock out/Tag
out systems when performing tests. Set up and perform tests of all
door systems (e.g., mechanical and electrical) to ensure related
cockpit instruments are functioning correctly.
* Apply sealant, alodine, primer, adhesives, and special
* Handle and dispose of hazardous materials in approved manner.
Operate mechanical lifts of various types to locate
parts/assemblies into position or to perform assembly work.
* Frequent (3-6 Hrs.) Handling (holding, grasping), Kneeling,
Sitting, Standing, Walking.
* Working around constant noise.
* Flexion/extension (head bent down, head bent back), finger
manipulation, handling, kneeling, bending at the waist, reaching
(overhead), Lying down (back, side, front), rotation of head/neck,
standing, twisting at the waist, walking.
* Climbing/balancing (stairs, ladders, poles, scaffolding, inclined
surfaces), Crawling, Crouching (squatting).
* Lifting and carrying up to 10-35 pounds.
This position is expected to be 100% onsite. The selected candidate
will be required to work onsite at one of the listed location
The position must meet Export Control compliance requirements,
therefore a "US Person" as defined by 22 C.F.R. - 120.15 is
required. "US Person" includes US Citizen, lawful permanent
resident, refugee, or asylee.
Basic Qualifications (Required Skills/Experience):
* 1 year experience using hand tools and/or hand-held power
Preferred Qualifications (Desired Skills/Experience):
* 1 year experience reading and interpreting drawings,
specifications, material processes, schematic and diagrams
* Attended a Boeing partnered manufacturing related high school or
community and technology college academic program
Typical Education & Experience:
High school diploma and/or General Education Diploma (GED)
Relocation assistance is not a negotiable benefit for this
position. Candidates must live in the immediate area or relocate at
their own expense.
Drug Free Workplace
Boeing is a Drug Free Workplace where post offer applicants and
employees are subject to testing for marijuana, cocaine, opioids,
amphetamines, PCP, and alcohol when criteria is met as outlined in
Union Representation Statement
This is an hourly position governed by the International
Association of Machinists (IAM-751) Collective Bargaining
Other Relevant Information & Requirements
Current Boeing employees working in Puget Sound and Portland must
submit an Employee Request Transfer (ERT) to be considered in the
eligible candidate pool. Resumes of current Puget Sound Boeing
employees submitted via Careers at Boeing will not be
Shift Work Statement
This position is for variable shift
Equal Opportunity Employer:
Boeing is an Equal Opportunity Employer. Employment decisions are
made without regard to race, color, religion, national origin,
gender, sexual orientation, gender identity, age, physical or
mental disability, genetic factors, military/veteran status or
other characteristics protected by law.
Contingent Upon Program Award
No, this position is not contingent upon program award
Apply Now Save JobRemove from Saved Jobs
Keywords: Boeing, Renton , Assembler Installer Doors B, Professions , Renton, Washington
Didn't find what you're looking for? Search again!